transparent.gif (43 bytes)
transparent.gif (43 bytes)

    Home|New Products|Quality System|Contact Us

Copper Tube
Solder
Copper Fittings
A/C Parts
Thermostat
Compressors
Vacuum Pumps
and Motors
Definite Purpose Contactors
Low Voltage Electrical
Capacitors
Controls
 
Location: Home >> Products >> Copper Tube >> Solder

 

 

Brazing Rings

To order please specify the following:
•  Quantity
•  Alloy
•  Wire Dianmeter(I.D.Ring or O.D.Ring)
•  Gap
•  I.D.Ring(max.)
•  O.D.Ring(max.)/ O.D.Ring(max.)
•  Helix(max.)
I.d.(Inside Diameter) Rings- specified when the brazing ring is to pre-placed on the outside of a tube.Little or no ga is preferred to allow the ring to expand and fit tightly on the tube without a substantial absence of filler metal in any area.

O.D.(Outside Diameter) Rings- specified when the brazing ring is to be pre-placed on the inside of a tube or fitting.A gap is required to allow the ring to contract and fit tightly inside the coupling without overlapping.

Helix- On I.D.Rings. Helix is kept to a minimum to facilitate automatic loading and prevent tangling

Partial or Multiple Turn Rings are available upon request.

Tolerances can often be held more tightly than the indicated standard tolerances at additional cost.This information must be specified on the original order

Drawings are not mandatory,but are preferrred.

Packaged in polyethylene bags,overpacked in corrugated carton,approximately 20,000 pieces per container(depend on ring size).Each box specifies the exact liquidus temperature on phos/copper alloys.

Mandrels(Do wels) O.D.ring are aavailable on mandrels to prevent tangling.Extra charges depend on ring size and quantity.


Brazing rod

Soldering Alloys

TYPICAL APPLICATION DATA©©

SS

AWSA5.8

Ag

Cu

Zn

Ni

Sn

Other

SOLIDUS F C

LIQUIDUS F C

FLUIDITY RATING

SS O

BCuP-2

92.9

7.1P

1310-710

1475-802

5

SS OLP

93.2

6.8P

1310-710

1510-821

4

SS OHP

BCuP-2

92.6

7.4P

1310-710

1445-785

6

SS OXHP

92.4

7.6P

1310-710

1415-768

7

SS 2

BCuP-6

2

91.0

7.0P

1190-643

1450-788

4

SS 2LP

2

91.4

6.6P

1190-643

1500-816

3

SS 2HP

2

90.6

7.4P

1190-643

1405-763

5

SS 5

BCuP-3

5

89.0

6.0P

1190-643

1500-816

3

SS 5LP

5

89.3

5.7P

1190-643

1535-835

2

SS 5HP

5

88.6

6.4P

1190-643

1445-785

4

SS 6

6

87.5

6.5P

1190-643

1425-774

5

SS 6LP

6

87.8

6.2P

1190-643

1455-791

4

SS 6HP

BCuP-4

6

86.8

7.2P

1190-643

1335-724

7

SS 15

BCuP-5

15

80.0

5.0P

1190-643

1480-804

3

SS 25

25

43

30

2

1270-668

1435-779

5

SS 30

BAg-20

30

38

32

1250-667

1410-766

6

SS 35

BAg-35

35

32

33

1250-667

1350-732

5

SS 38T

BAg-34

38

32

28

2

1220-660

1325-718

7

SS 40

40

30.5

29.5

1250-667

1350-732

5

SS N12

BAg-4

40

30

28

2

1220-660

1435-779

4.5

SS 40T

BAg-28

40

30

28

2

1220-660

1310-710

6.5

SS 45

BAg-5

45

30

25

1225-663

1370-743

6.5

SS 45T

BAg-36

45

27

25

3

1195-643

1265-685

7

SS 50

BAg-6

50

34

16

1270-688

1425-774

5.5

SS 50N

BAg-24

50

20

28

2

1220-660

1305-707

7

SS 54

BAg-13

54

40

5

1

1325-718

1575-857

4

SS 56

BAg-7

56

22

17

5

1145-618

1205-652

8

SS 72

BAg-8

72

28

1435-779

1435-779

 

Total thickness

70¦Ì

Inside facing

33¦Ì

Outside facing

27¦Ì

Spacing between springs wires

15mm(ID 2")/25mm(ID 4")/35(ID 6")

shrinkage after fully extended

5%

Service temperature

-30¡æ~140¡æ

Maximum air pressure

250 W.G.

Maximum Air Velocity

30 Meters/sec(6,000 ft/min)



P.O. BOX 741074 • DALLAS, TEXAS 75374 • USA TEL:(972) 563-9289 • FAX:(972) 563-5783transparent.gif (43 bytes)email: info@kg-ind.com